Top 10 typical forklift mishaps ， forklift procedure must take notice of these issues ！.

Top 10 typical forklift mishaps ， forklift procedure must take notice of these issues ！.

Blog Article

Do not ignore the forklift at work. If the operation is bad, there will certainly be serious mishaps in minutes, and there are lots of mishaps including forklifts.

Instance 1: The forklift freight obstructed the vehicle driver's view, and the individual ahead can not be located, causing a moving crash.
Instance 2: In order to keep the equilibrium of the forklift when raising hefty products, the workers used their body weight as the counterweight, which almost caused casualties.
Case 3: The size of the forklift freight surpasses the permitted width of the route and holds on the roadside rack, which nearly triggers an mishap.
Case 4: Forklift is speeding up and surrender during a turn.
Case 5: The forklift driver did not notice the pedestrian, and the pedestrian did not see the forklift.
Instance 6: The forklift lifts the personnel unlawfully, the forklift motorist does not use the seat belt, the forklift lifter drops and the motorist is crushed when the forklift surrender.
Situation 7: The forklift chauffeur did not wear a safety belt and fell from the vehicle when it surrendered and was crushed.
Forklift procedure must focus on these issues ：.

Begin.
1. Before beginning, observe the surroundings, and after validating that there are no challenges that hinder the safety and security of driving, honk the horn initially and after that start.
2. For automobiles with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale should be safe before beginning.
3. When the forklift starts with a lots, the chauffeur should initially validate that the tons is secure and trustworthy.
4. The start needs to be slow and consistent.

Driving.
1. When driving, the height between the bottom end of the fork and the ground need to be kept at 300mm-400mm, and the pole should be tilted in reverse. .
2. Do not lift the fork too expensive when driving. When entering and leaving the task website or while driving, be careful that there will certainly be no barriers in the sky. When the tons is taking a trip, the fork should not be elevated too high, which will influence the security of the forklift. .
3. After discharging, the fork should be decreased to the typical driving setting before driving. .
4. When turning, if there are pedestrians or vehicles nearby, the driving signal needs to be provided initially. High-speed sharp turns are prohibited. High-speed doglegs will trigger the vehicle to lose lateral security and tip over. .
5. When the forklift is downhill, it is purely restricted to shut off the fire and slide, and it is forbidden to brake suddenly while driving with lots unless there are unique conditions.
6. When the forklift is running, it should obey the traffic rules in the manufacturing facility and should maintain a particular safety range from the vehicle ahead. .
7. When the forklift is running, the load has to be in the most affordable placement that does not impede the driving, and the gantry must be appropriately slanted back. The lots will not be increased except when stacking or packing. .
8. The elevation of the load need to not obstruct the chauffeur's sight. In special situations, when the product affects the forward vision, drive at a low speed when turning around.
9. It is forbidden to switch on the ramp, neither to drive throughout the ramp. .
10. The secure driving speed of the forklift in the manufacturing facility area is 5 km/h, and it needs to drive securely at a reduced speed when getting in the manufacturing workshop area. .
11. When the forklift is raised, lifted or driven, it is restricted for employees to depend on the fork to hold things and play a stabilizing duty. .
12. If problems are found, they will certainly be fixed and reported in a timely fashion, and they will never operate with illnesses or conceal them.

loading and discharging.
1. When fork-loading things, the range in between both forks must be readjusted as required to make the load of both forks balanced and not manipulated, and one side of the product should be against the shelf. .
2. It is restricted to collaborate with a single fork or utilize a fork top or draw. In special situations, security indication need to be established to remind surrounding pedestrians. .
3. In the process of loading and unloading products, the forklift should be stopped with the brake. .
4. The speed of the lorry ought to be slow-moving and consistent. Take care not to roll the wheels on the dunnage, so as not to stretch the rolled things and harm people. .
5. When using a fork to fork the goods, the fork must be as deep as feasible under the tons, and it ought to be noted that the fork tip must not touch other items or objects. The tons ought to be supported with marginal back tilt of the gantry to make sure that the load does not glide backwards. The pole can be tilted ahead a little when the lots is lowered to permit easy positioning of the load and removal of the forks. .
6. It is forbidden to fork products at broadband and collide with difficult items with the fork head. .
7. When the forklift is working, it is prohibited for people to loaf the fork, so regarding avoid the collapse of the goods and harm people. .
8. Straining is forbidden, and it is prohibited to utilize forks to raise workers to participate in high-altitude procedures to stay clear of high-altitude dropping crashes. .
9. It is not allowed to utilize the brake inertia to slip, put, round or roll items. .
10. It is not allowed to utilize forks to choose, transform pallet unload.

Leaving Stand-on Electric Pallet Stacker .
1. It is restricted to leave the forklift when the products on the fork impend. Before leaving the forklift, you need to dump the Stand-on Electric Pallet Stacker goods or lower the fork framework.
2. Pull the parking brake deal with to dead or depress the hand brake button.
3. The engine is switched off and the power is cut off. (Except for unique circumstances, such as the driver does not leave the lorry's view and does not surpass 1 minute).
4. Remove the secret. .

Forklift Operation Precautions.
1. Prior to and after the forklift procedure, the look should be checked, and gas, lubing oil and air conditioning water need to be added.
2. Examine the safety and security efficiency of starting, running and stopping.
3. Examine whether the lights and horn signals are total and effective.
4. During the procedure of the forklift, inspect whether the pressure and temperature are normal.
5. After the forklift is running, the outside leak should also be inspected and the seals should be changed in time.

Forklift Safety Operation Specifications.
1. You must inspect prior to leaving the car;.
2. When you experience somebody in front of you during driving, you need to send a signal at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not surpass 5 km/h;.
4. When driving, the low point of the cargo ought to be 0.3 m ~ 0.4 m above the ground;.
5. The transforming ought to not be as well sharp to avoid the tendency of " totally free turning";.
6. Running up and down the incline must be sluggish and uniform, and no switching on the incline is permitted.
7. Do not drive throughout the slope. When the slope is higher than 10%, the vehicle ought to be driven backwards when declining;.
8. When the forklift workers lug the goods and move on, if they experience big or heavy items and most likely to the motorist's view, they need to take the turning around exercise
.
The "Eight Prohibitions" must be complied with in the operation.
1. Solitary fork operation is not allowed.
2. It is not allowed to lift the goods for cross country driving.
3. It is not enabled to grab the goods by passing on the pallet with the fork.
4. It is not permitted to straight shovel chemicals, flammables and other harmful chemicals with forks.
5. It is not allowed to utilize inertia force to get the goods.
6. It is not allowed to use stopping pressure to expatriation round or easy-to-roll objects.
7. It is not allowed to bring individuals to work with the pallet or fork, and it is strictly restricted to stand under the fork after the fork is increased.
8. Do not drive side to side on slopes
.
Auto parking is not allowed under the following problems.
1. Curves, narrow roadways, train crossings;.
2. Areas with a longitudinal incline higher than 5%.
3. When there is an obstacle on one side of the roadway, the opposite side of the section with the exact same size as the obstacle should be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：info2@onen.cn
Phone：+86 13827083844